# Tapping saddle: how to add a branch without welding

> How to take a branch off a polyethylene pipe with a tapping saddle: choosing the size, fitting it and drilling the pipe, and whether you can tap in under pressure.

Web page: https://watertrade.com.ua/en/articles/article/homut-dlya-vrezki-v-trubu · Other languages: [UA](https://watertrade.com.ua/articles/article/homut-dlya-vrezki-v-trubu.md), [RU](https://watertrade.com.ua/ru/articles/article/homut-dlya-vrezki-v-trubu.md)

*November 18, 2026*

![Diagram: buried HDPE pipe, a two-piece bolted tapping saddle, a branch with a ball valve and a drill passing through the open valve](https://watertrade.com.ua/uploads/articles/tapping-saddle.jpg)

You need an extra tap for the garden or want to connect a sauna or outdoor shower to an existing pipe, without cutting the main and fitting a tee. That is what a tapping saddle is for: it clamps onto the pipe and the branch is made through a single hole. The job takes half an hour and needs no welding.

## What the diagram shows

1 — the HDPE pipe, 2 — the two-piece bolted tapping saddle, 3 — the threaded branch with a ball valve, 4 — a drill passing through the open valve.

## Choosing a saddle

- **By the pipe’s outside diameter** — 25, 32, 40, 50 or 63 mm, printed on the pipe.
- **By the branch thread** — 1/2", 3/4", 1" and up. The branch cannot be larger than the pipe: a 32 mm pipe usually takes 1/2"–3/4".
- The saddle is rated for the same pressure as the pipe — check the PN marking.

## Installation step by step

1. Shut the water off and release the pressure — easier and safer.
2. Clean the pipe section of dirt and sand: not a single grain should sit under the sealing ring.
3. Fit the lower and upper halves of the saddle (2), with the branch facing up or to the side where the new line will run.
4. Tighten the bolts **evenly, in a criss-cross pattern**, so the saddle sits square and the ring is not skewed.
5. Screw a ball valve (3) into the branch with thread sealant.
6. Drill the pipe through the open valve with a plastic drill bit or hole saw (4), 4–6 mm smaller than the branch’s internal diameter. Drill slowly and straight.
7. Withdraw the drill and flush the branch so no swarf enters the system. Connect the new line.

> Technically you can tap in under low pressure: drill through the open valve and close it as soon as the drill comes out. But water will spray and swarf will go into the pipe. On a water utility street main, tapping is done only with permission and by the utility itself.

## Where a saddle will not work

- On PP-R and multilayer pipes — use a tee or a weld-on saddle instead.
- On old, cracked or badly scratched pipe — the ring will not seal.

Saddles are grouped in [tapping saddles](https://watertrade.com.ua/en/catalogue/truby-i-fitingi/fitingi-dla-pnd-trub/products/homuty-dlya-vrezki), pipe in [HDPE pipes](https://watertrade.com.ua/en/catalogue/truby-i-fitingi/fitingi-dla-pnd-trub/products/truby-pnd), fittings for the new line in [32 mm HDPE fittings](https://watertrade.com.ua/en/catalogue/truby-i-fitingi/fitingi-dla-pnd-trub/products/fitingi-pnd-32-mm), valves in [1/2" ball valves](https://watertrade.com.ua/en/catalogue/zapornaa-armatura/sarovye-krany/products/sharovye-krany-1-2). How to assemble an HDPE line — see “HDPE compression fittings”; summer plumbing — [here](https://watertrade.com.ua/en/articles/article/letnij-vodoprovod-na-dache).

---

Watertrade · sale@watertrade.com.ua · Site map for language models: https://watertrade.com.ua/en/llms.txt
