# Water pressure booster pump for a flat or house

> When a booster pump helps, how an inline pump with a flow switch differs from a booster set, where to install it and why it soon fails without a strainer.

Web page: https://watertrade.com.ua/en/articles/article/nasos-dlya-povysheniya-davleniya · Other languages: [UA](https://watertrade.com.ua/articles/article/nasos-dlya-povysheniya-davleniya.md), [RU](https://watertrade.com.ua/ru/articles/article/nasos-dlya-povysheniya-davleniya.md)

*November 20, 2026*

![Diagram: water inlet with a valve, strainer, booster pump with flow switch, washing machine and shower](https://watertrade.com.ua/uploads/articles/booster-pump.jpg)

A trickling shower, a gas water heater that will not ignite, a washing machine that takes half an hour to fill — familiar to people on upper floors and in dacha villages. A booster pump adds pressure right at the inlet of the flat or house. It does not always help, though, and choosing the right type matters.

## What the diagram shows

1 — water inlet with a ball valve, 2 — a strainer, 3 — a booster pump with a flow switch, 4 — a mixer tap and shower (a washing machine next to it).

## First find the cause

A pump can only raise pressure if there is water in the pipe. Open the inlet valve: if pressure is weak everywhere and all the time, the mains is the problem and a pump will help. If only hot water or a single tap is weak, look for a blockage, a clogged aerator or filter — see [“Low water pressure”](https://watertrade.com.ua/en/articles/article/slabyj-napor-vody). If water disappears completely in the mornings, you need a [storage tank](https://watertrade.com.ua/en/articles/article/zapas-vody-nakopitelnyj-bak) and a booster set.

## Types of pump

- **Inline pump with a flow switch** — small, fitted straight into a 1/2"–3/4" pipe. It starts by itself when a tap is opened and adds roughly 1–1.5 bar. Quiet; suits a flat, a water heater or a gas geyser.
- **Booster set with a tank** — more powerful, holds pressure via a pressure switch and can draw from a tank when the mains is dry. Needed when the whole house lacks pressure or supply is intermittent.

> In an apartment block, a powerful pump connected straight to the riser takes water from the neighbours above. Fit a small pump for your own flat, and if the supply is very weak use a tank and a booster set, so the pump draws from the tank rather than the shared pipe.

## Installation step by step

1. Turn the water off. The pump goes after the meter: **valve → strainer → pump → valve**.
2. **The strainer is a must**: sand and scale quickly jam the impeller and the flow switch.
3. Fit the pump following the arrow on the body. Wet-rotor pumps need a horizontal shaft — check the manual.
4. Plug it into an earthed socket; the spot should be dry and accessible for servicing.
5. Open the water, bleed the air and choose the mode: “auto” starts on flow, “manual” runs constantly (for testing only).

Inline pumps are in [pressure booster pumps](https://watertrade.com.ua/en/catalogue/nasosy/nasosy-dla-povysenia-davlenia), booster sets in [booster sets with a 24 L tank](https://watertrade.com.ua/en/catalogue/nasosy/nasosnye-stancii/products/nasosnye-stancii-24-l), and strainers in [Y-strainers](https://watertrade.com.ua/en/catalogue/filtry-dla-vody/setcatye-filtry/products/kosye-filtry). How to connect a booster set — see [“Booster set for a private house”](https://watertrade.com.ua/en/articles/article/skhema-podklyucheniya-nasosnoj-stancii).

---

Watertrade · Phone: (093) 917-25-45 · sale@watertrade.com.ua · Site map for language models: https://watertrade.com.ua/en/llms.txt
